I intend to fit 4-5 lamps - would I need to buy any additional items to link them up or would they run off 1 of the transformers supplied in the kit
Each kit you buy comprises of a downlight, a lamp and a transformer. You could link all your downlights to one transformer however you need to ensure the transformer has the correct capacity. We would recommend you use one transformer per downlight.
|
Are these lights ok to put in pvc soffits or do they stain it with the heat?
These fittings are F Marked making them suitable for use in/on flammable materials. Heat and UV light will discolour uPVC but heat will be dissipated when used outdoors. If these were to be fitted inside i.e. in a porch we'd suggest a 35 or even 20 watt lamp.
|
Is this available in other colours (grey/chrome)? What is the visible light opening diameter? Are bulbs replaced from below?
This kit uses a our standard IP65 downlight (found in our bathroom downlight section) which is also available in a polished chrome and satin nickel finish with a transformer and a long life lamp. Whilst we have never tested this fitting in finishes other than white in an exterior setting, it is IP65 and so offers suitable protection for this application. If you wish to have this soffit kit with a fitting in another finish please contact us and we'll change the components to suit.
|
Can I replace my old ones with this kit, there is nothing realy wrong with the old other than the outer is rusty?
Being powdercoated paint and made from an alloy means these should last longer than your old fittings. Just check they are the same cut-out.
|
can I get these lamps in black? I want to put them outside i the soffits. Also, can I put GU10 LED bulbs in them?
The lamps are only available in white, you can tho use a GU10 LED lamp with these.
|
Can these lights be used with a PIR?
Yes these lights can be operated by a PIR without any issues.
|
Are these available with a brass finish? If so how much and what is the order code?
Unfortunately we do not as yet have an IP rated downlight in a brass finish.
|
I intend fitting approx 12 of these to my newly installed UPVC soffets, what bulb would you suggest to minimise heat and maximise bulb life?
If you are wishing to be both a friend to the earth and your pocket then consider using retro fit LED lamps. These will run cool, consume very little energy in comparison to standard halogen lamps. The initial outlay is greater, however with a lamp life of around 30,000 hours its really more of an investment!
You can view Retro fit LED lamps via the following link:
www.lightingstyles.co.uk/High_Power_3W_Retrofit_LED_Lamp.htm
|
What size wiring would be required to typically install 6 of these in series and will your PIR/Dusk till Dawn sensor work with these ok.
If you're using 50w lamps the load would be 50w x 6 = 300w. 300w ÷ 240v = 1.25 amps i.e. pretty much any cable with conductors 1.0mm or larger.
|
does the lamp fitting come with gu10 fitting ? if not can they be swapped ?
This fitting is designed for MR16 lamps (12V - Low voltage). Try the 90 Min IP65 Fire Rated Downlight product reference: SAMDLF805, or the Tilted Downlight product reference: NX20290131.
|
I am looking to fit down lights to my soffit boards, i have cut 60mm holes can you tell me if these would fit? And what clearance is need above the fitting when in place? Also can this fitting be used with your dusk till dawn sensor? Also do the lamps have to be earthed?
The suggested cut-out is 70mm so your holes may need enlarging slightly. The transformer powering this lamp can work on a dusk til Dawn sensor and being double insulated do not need an earth.
|
Can you please tell me the height of this fitting from top to bottom?
The height of the fitting would exclude the lamp and lamholder (and therefore be of no use). The void required is 85mm a little less is okay.
|
Can these fittings be used with an LED lamp?
Yes you can used the downlight with our ideal fit lamp - it's a little fiddly to install because of the fins on the lamp but once in place will give long lamp life. You will need to buy:
1 x SAMDL805 - the fitting
1 x SAMLHGU10 - the GU10 lampholder
1 x SAM39977 - ideal fit 5w LED lamp
|
What is the diameter of the actual light area? Is the glass clear or frosted as i want a glow affect?
The diameter of the clear glass is 40mm.
|
Does this kit come with two light fittings?
purchasing one kit will get you one downlight, one transformer and one 50w 60º lamp.
|
Sorry when i said height of fitting,i actually meant the depth of the fitting?
The listing already has a depth given under specification tab. It is 4mm
|
